Noyes OPM5-4D OPM-5-4D SM MM Fiber Power Meter Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
Noyes OPM5 Power Meter
The OPM 5 is used to perform diagnostic and evaluation measurements associated with fiber optic transmission systems and cable plant. Applications for the OPM 5 will be found within the telecommunication, cable television, data network, and industrial control industries.
The OPM 5 measures absolute power (in dBm or µW ) and loss (dB). Absolute power expressed in dBm is the amount of optical power received by the detector as compared to 1mW (0dBm=1mW). Measuring dBm is useful for verifying the output power of a transmitter and determining system losses.
Loss is the difference in optical power from a known input (the reference level) and the output power at the opposite end of the fiber under test. The OPM 5 can display dB loss directly after a reference level has been set. Loss measurements are used to qualify cable plant links and fiber optic jumpers.
Microwatts is also a way to measure absolute power. Some manufacturers specify their transmission equipment in watts instead of dBm. The OPM 5 offers the ability to measure watts for convenience when verifying output power of transmitters. For accurate results, always be sure to set the OPM 5 to measure the same wavelength as the output of the optical light source.
AFL Noyes OPM5-4D Optical Power Meter (BC# 17285)
Power Meter:
-850nm
-980nm
-1310nm
-1490nm
-1550nm
-1625nm
ST Connector For Power Meter
SM ST-ST Fiber Cable
MM ST-ST Fiber Cable
User Manual On CD-ROM
Carrying Case
Noyes OPM5-2 OPM-5-2 SM MM Fiber Power Meter Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
OPM 5-2
The OPM 5 is used to perform diagnostic and evaluation measurements associated with fiber optic transmission systems and cable plant. Applications for the OPM 5 will be found within the telecommunication, cable television, data network, and industrial control industries.
The OPM 5 measures absolute power (in dBm or µW ) and loss (dB). Absolute power expressed in dBm is the amount of optical power received by the detector as compared to 1mW (0dBm=1mW). Measuring dBm is useful for verifying the output power of a transmitter and determining system losses.
Loss is the difference in optical power from a known input (the reference level) and the output power at the opposite end of the fiber under test. The OPM 5 can display dB loss directly after a reference level has been set. Loss measurements are used to qualify cable plant links and fiber optic jumpers.
Microwatts is also a way to measure absolute power. Some manufacturers specify their transmission equipment in watts instead of dBm. The OPM 5 offers the ability to measure watts for convenience when verifying output power of transmitters. For accurate results, always be sure to set the OPM 5 to measure the same wavelength as the output of the optical light source.
Order Separately (ST, SC, FC and others available)
Size (H x W x H)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.56 lb (0.26 kg)
Operating Temp
0° to 50° C
Storage Temp
30° to 60° C
Relative Humidity
0 to 95% (non-condensing)
Condition: Refurbished
Warranty: 90 Day Exchange
Included:
AFL / Noyes OPM 5-2 Optical Power Meter (BC# 16515)
-850nm
-1300nm
-1550nm
-Interchangeable ST Connector For Power Meter
SM SC-SC Fiber Cable
MM SC-SC Fiber Cable
User Manual On CD-ROM
Carrying Case (G)
NOYES OPM5 Singlemode Multimode Loss Test Set
OPM5-2C SM MM Power Meter w/
OLS1D MM 850 / 1300nm Dual Light Source
&
OLS2D SM 1310 / 1550nm Dual Laser Source
Noyes OPM5 OLS1D OLS2D OPM-5 OLS-1D OLS-2D SM MM Fiber Loss Test Set Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
OLS2D
The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port and offers several modes of operation. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.
Features:
Handheld, rugged, lightweight
Dual wavelengths from a single port
Dual or single Wave ID, CW, To
270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
Adjustable output
Low battery LED indicator
Long battery life with 2 x AA alkaline, optional AC adapter
Cost-effective, easy to use
N.I.S.T. Traceable
Applications:
Certify SM links per TIA/EIA standards
Fiber identification prior to splicing
OLS1D
NOYES OLS1-Dual is a hand-held, rugged LED light source designed for performing insertion loss measurements on multimode fiber optic links when used with an optical power meter. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements.
Multimode Output Port; emits 850/1300 nm LED output at CW, WaveID, or dual wavelength WaveID.
Faster Test Times with WaveID – In WaveID mode, the NOYES OLS4 encodes each wavelength with a unique WaveID code. When used with a NOYES power meter, the pair can send and receive two wavelengths each test – doubling testing efficiency – reducing test time! Flexible Output Connector Adapter Design The OLS1-Dual output ports are equipped with UCI based removable adapters to allow the output connectors to be inspected and cleaned, while allowing field change of output style between FC, SC, ST, & LC connector adapters.
50 and 62.5 µm fiber mandrels Included Mandrels condition test cable for use in certifying both 50 and 62.5 µm fiber links for current and planned high bit rate applications including Gigabit Ethernet and 10 Gigabit Ethernet. Mandrels apply to launch jumpers is seconds without tools and ensure loss measurements comply with TIA/EIA-568-B standard.
Hand-held, rugged, lightweight
Dual wavelengths from a single port
Dual or single Wave ID, CW, Tone Output
Selectable 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
Applications:
Certify 50 or 62.5µm fiber links to TIA/EIA Standards
Certify Multimode fiber links for Gigabit Ethernet (GBE)
Test Ethernet, Token Ring, and FDDI fiber networks
Use 1300 nm port to test up to 10 km single-mode fiber links
OPM 5-2C
The OPM5 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 5 also measures insertion loss of multimode or single-mode cables.
The OPM5 offers Wave ID, automatic wavelength identification and switching, when used with the OLS1-Dual, OLS2-Dual, or OLS4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM5 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. Up to 500 records per wavelength of power or insertion loss measurements may be stored in internal non-volatile memory.
Using the supplied Windows® compatible software and USB connection, test records may be transferred to a PC for storage, display, printing, and analysis. In addition to being powered by two AA alkaline, the OPM5 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM5 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately.
The OPM5 is fully N.I.S.T. traceable.
Features:
Rugged, handheld, lightweight
Multimode or single-mode applications
Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
Wave ID – automatic wavelength identification and switching
Passive Optical Networks (PON) testing
Dual Wavelength testing
270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
Large LCD with Backlight
Power measurements in dBm or µW; insertion loss in dB
Reference power level storage
Up to 500 test records per wavelength storage and download
USB port for download of stored records
Free Windows® compatible software to view, print, and archive test records
AA alkaline, optional rechargeable NiMH battery pack
Battery Gauge
N.I.S.T traceable
Specifications:
Calibration Wavelength (nm)
850, 1300, 1310, 1550nm
Tone Detection Range (dBm)
+6 to – 35
Tone Detection Frequency (Hz)
270 ± 13.5
1000 ± 50
2000 ± 300
Detector Type
Germanium (Ge)
Display Range (dBm)
+6 to -60 dBm
Accuracy (@ 25°C & -10.0dBm)
±0.25 dB
Resolution
0.01 dB (.1 dB selectable)
Battery Life
>30 hrs. typical operation with 9V Alkaline
Adapter Caps
Order Separately (ST, SC, FC and others available)
Size (H x W x H)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.56 lb (0.26 kg)
Operating Temp
0° to 50° C
Storage Temp
30° to 60° C
Relative Humidity
0 to 95% (non-condensing)
Condition: Refurbished
Warranty: 90 Day Exchange
Included
AFL Noyes OPM5-2C Optical Power Meter (BC# 14508)
Power Meter:
-850nm
-1300nm
-1310nm
-1550nm
Interchangeable ST Connector For Power Meter
Noyes OLS1D Multimode Dual Light Source (BC# 16518)
MM Source:
-850nm
-1300nm
ST Connector For Source
Noyes OLS2D Singlemode Dual Laser Source (BC# 16516)
SM Source:
-1310nm
-1550nm
ST Connector For Source
(2) SM ST-ST Fiber Cables
(2) MM ST-ST Fiber Cables
User Manual On CD-ROM
Carrying Case
Loss Measurements at 850 and 1300 nm
Multimode and Singlemode Testing
Set Reference for Each Wavelength
Small Size, Field Portable, Battery Operated
Auto or Manual Power Off
N.I.S.T. Traceable
The MLP 4-2 Test Kit offers accurate fi ber optic testing at an affordable price. Combining the OPM 4-2C Optical Power Meter and the OLS 1-2 Optical Light Source in a rugged carry case, the MLP 4-2 is a complete Test Kit for fi ber optic LAN’s, and WAN’s.
Used during installations or maintenance, the MLP 4-2 performs insertion loss measurements on multimode fi ber at 850 and 1300nm, as well as singlemode fi ber at 1300nm. The auto zero feature stores reference values at each wavelength for direct loss readings in dB.
The OLS1-Dual LED light source is a cost-effective, rugged, handheld instrument designed for performing insertion loss measurements on fiber optic links when used with an optical power meter. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements.
The OLS1-Dual features 850 nm and 1300 nm LED output from a single output port and is easy to operate with only a power button and a wavelength select button. This light source offers 3 modes of operation: Dual wavelengths sending ID, single wavelength sending ID, and CW. [Active Output], [Battery], and [External Power] indicators identify the currently enabled operating mode, battery charge status, and external power presence. The output port is equipped with a removable SC (FC & ST available) adapter to allow the output connector to be inspected and cleaned.
The MLP 1 test kits are inexpensive solutions for testing multimode and single-mode systems. By joining the OPM 1 optical power meter and the OLS 1 optical light source, the MLP 1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit are available for testing Premises networks, LAN, and Gigabit Ethernet.
Features:
Multimode Testing
Loss measurements at 850 and 1300nm
Includes 50 and 62.5 µm mandrels
Field portable, battery operated
Certify 50 or 62.5 µm multimode fiber links for any 850 or 1300nm application, including Gigabit Ethernet (GBE)
N.I.S.T. traceable
Output ports
2
Output wavelength
850 + 35/-40 nm
1300 + 50/-10 nm
Spectral width (typ) (FWHM)
40 nm
120 nm
Output power
-20 dBm
>-20 dBm
Stability (@25°C, 5 min. warm-up)
0.1 dB over 8 hours
Fiber size
62.5 µm
Emitter type
Class 1 (IEC 60825 – 1)
Power
Typical 60 hours with 9V battery, optional AC adapter
Connector
ST
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.65 lb (.29 kg)
OPM 1
This portable optical power meter may be used to measure optical power in premises, telco, or broadband fiber optic networks. When used with an LED or laser light source, the OPM 1 can also measure the attenuation (insertion loss) of multimode or single-mode cables. With only two controls – ON/OFF and wavelength – the OPM 1 is our simplest to use optical power meter. Optical power in dBm and the calibration wavelength setting are displayed on an easy-to-read LCD display. The optical input port accepts Noyes thread-on style connector adapter caps. Adapter caps are required and must be ordered separately. The OPM 1 is fully N.I.S.T. traceable and runs on a standard 9-volt alkaline battery.
AFL NOYES OPM 4-4 Power Meter w/ OLS1-2C 850/1300nm Multimode Light Source
Multimode Loss Test Set
NOYES OPM 4-4 Optical Power Meter
– 850nm
– 1300nm
– 1550nm
Includes Carrying Case & Accessories As Listed
OPM 4-4 OPM4 OPM 4 OPM 4-4 OLS1 2C
Noyes OPM4-4 OLS1-2C OPM-4-4 OLS-1-2C MM Fiber Loss Test Set Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
OPM 4 Optical Power Meter
The OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables. The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.
Features:
Rugged, handheld, lightweight
Multimode or single-mode applications
Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
Wave ID – automatic wavelength identification and switching
Passive Optical Networks (PON) testing
Dual Wavelength testing
270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
Large LCD with Backlight
Power measurements in dBm or µW; insertion loss in dB
Reference power level storage
AA alkaline, optional rechargeable NiMH battery pack
Battery Gauge
N.I.S.T traceable
Condition: Refurbished / Calibrated
Warranty: 90 Day Exchange
Included
Noyes OPM 4-4 Optical Power Meter (BC# 14945)
-850nm
-1300nm
-1550nm
-Interchangeable ST Connector
Noyes OLS1-2C Optical Light Source (BC# 14943)
-850nm
-1300nm
-(2) Interchangeable ST Connectors
(2) MM ST-ST Fiber Cables
User Manual On CD-ROM
Carrying Case w/ Strap
AFL NOYES OPM4 Singlemode 1310nm/1550nm & Multimode 850nm/1300nm Loss Test Set
NOYES OPM 4-4C Optical Power Meter
850nm
1300nm
1310nm
1550nm
NOYES OLS2 Dual Laser Source
1310nm
1550nm
Noyes OLS1 Dual Optical Light Source
850nm
1300nm
Includes Carrying Case & Accessories As Listed
OPM4-4 C OLS2-D OLS 1-D 1
Noyes OPM4 OPM-4 SM MM Fiber Loss Test Set Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
OLS1 Dual Light Source
OPTICAL
OLS1-DUAL (SINGLE PORT)
Wavelength
850 ±30 nm
1300 +50/-10 nm
Emitter Type
LED,Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral Width
40 nm (typ)
120 nm (typ)
Output Power
>-20 dBm b
Output Stability
±0.1 dB over 8 hours (after 5-minute warm-up)
Fiber Size
62.5 µm c
GENERAL
Power
2 AA batteries, optional AC adapter
Battery Life
Typical 30 hours, minimum 20 hours
Available Adapters
SC, FC, ST
Operating Temperature
-10°C to 50°C, 90 % RH (non-condensing)
Storage Temperature
-30°C to 60°C, 90 % RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
OLS2 Dual Laser Source
The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port and offers several modes of operation. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.
Features:
Handheld, rugged, lightweight
Dual wavelengths from a single port
Dual or single Wave ID, CW, To
270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
Adjustable output
Low battery LED indicator
Long battery life with 2 x AA alkaline, optional AC adapter
Cost-effective, easy to use
N.I.S.T. Traceable
Applications:
Certify SM links per TIA/EIA standards
Fiber identification prior to splicing
The Noyes OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables.
The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.
The OPM 4-4C is calibrated at 850, 980, 1310, 1550, nm and designed for the higher power level requirements of long range, amplified optical spans used in CATV and DWDM networks.
Specifications:
Optical Specifications
OPM 4-4C
Calibrated Wavelengths (nm)
850, 1300, 1310, 1550
Detector Type
Filtered InGaAs
Measurement Range (dBm)
+26 to -50
Accuracy (dB)
+-.25
Measurement Units
dB, dBm, uW
General Specifications
Power
typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Operating temperature
-10 to 50°C
Relative humidity
0 to 95% (non-condensing)
Storage temperature
-30 to 60°C
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
Condition: Refurbished / Calibrated
Warranty: 90 Day Exchange
Included
Noyes OPM 4-4C Optical Power Meter (BC# 09805)
-850nm
-1300nm
-1310nm
-1550nm
-Interchangeable ST Connector
-Interchageable FC Connector
Noyes OLS1 Dual Light Source (BC# 14053)
-850nm
-1300nm
-Interchangeable ST Connector
Noyes OLS2 Dual Laser Source (BC# 14002)
-1310nm
-1550nm
-Interchangeable FC Connector
Noyes 5400-00-0201 Mandrell w/ Instructions
Noyes 5400-00-0202 Mandrell w/ Instructions
Fiber Cables:
-(2) SM ST-ST
-(2) MM SC-ST
-Interchangeable SC-SC
-Interchangeable ST-ST
Hard Copy User Manual
User Manual On CD-ROM
Carrying Case
OPM 5-2C
The OPM 5 is used to perform diagnostic and evaluation measurements associated with fiber optic transmission systems and cable plant. Applications for the OPM 5 will be found within the telecommunication, cable television, data network, and industrial control industries.
The OPM 5 measures absolute power (in dBm or µW ) and loss (dB). Absolute power expressed in dBm is the amount of optical power received by the detector as compared to 1mW (0dBm=1mW). Measuring dBm is useful for verifying the output power of a transmitter and determining system losses.
Loss is the difference in optical power from a known input (the reference level) and the output power at the opposite end of the fiber under test. The OPM 5 can display dB loss directly after a reference level has been set. Loss measurements are used to qualify cable plant links and fiber optic jumpers.
Microwatts is also a way to measure absolute power. Some manufacturers specify their transmission equipment in watts instead of dBm. The OPM 5 offers the ability to measure watts for convenience when verifying output power of transmitters. For accurate results, always be sure to set the OPM 5 to measure the same wavelength as the output of the optical light source.
Specifications:
Calibration Wavelength (nm)
850, 1300, 1310,
1550nm
Tone Detection Range (dBm)
+6 to – 35
Tone Detection Frequency (Hz)
270 ± 13.5
1000 ± 50
2000 ± 300
Detector Type
Germanium (Ge)
Display Range (dBm)
+6 to -60 dBm
Accuracy (@ 25°C & -10.0dBm)
±0.25 dB
Resolution
0.01 dB (.1 dB selectable)
Battery Life
>30 hrs. typical operation with 9V Alkaline
Adapter Caps
Order Separately (ST, SC, FC and others available)
Size (H x W x H)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.56 lb (0.26 kg)
Operating Temp
0° to 50° C
Storage Temp
30° to 60° C
Relative Humidity
0 to 95% (non-condensing)
Condition: Refurbished
Warranty: 90 Day Exchange
Included
AFL / Noyes OPM 5-2C Optical Power Meter (BC# 14051 14508)
-850nm
-1300nm
-1310nm
-1550nm
-Interchangeable ST Connector
Fiber Cables:
-MM ST-ST
-SM ST-ST
User Manual On CD-ROM
Includes Hard Carrying Case & Accessories As Listed
MLP5-2 OLS-1 OLS 1 OPM5-2 OPM5-2C
Noyes MLP2B MLP-2B MM Fiber Loss Test Set Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
Noyes Multimode Test Set (MLP 5-2B)
The Noyes MLP5-2 fiber optic loss test kit combines the OPM5-2C optical power meter and OLS1-Dual LED light source and is ideally suited for testing multimode fiber optic networks.
The OLS1-Dual features 850 nm and 1300 nm LED output from a single output port and is easy to operate with only a power button and a wavelength select button. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements. This light source offers 3 modes of operation: Dual wavelengths sending ID, single wavelength sending ID, and CW. [Active Output], [Battery], and [External Power] indicators identify the currently enabled operating mode, battery charge status, and external power presence. The output port is equipped with a removable SC (FC & ST available) adapter to allow the output connector to be inspected and cleaned.
The OPM5-2C offers Wave ID, automatic wavelength identification and switching, when used with the OLS1-Dual light source. The OPM5-2C stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or ¼W] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. Up to 500 records per wavelength of power or insertion loss measurements may be stored in internal non-volatile memory.
Using the supplied Windows® compatible software and USB connection, test records may be transferred to a PC for storage, display, analysis, and printing.
In addition to being powered by two AA alkaline, the OPM5-2C or OLS1-Dual can be powered by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM5-2C optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately.
The OPM5-2C and OLS1-Dual are fully N.I.S.T. traceable.
Rugged, handheld, lightweight
Designed for field use
Certify multimode fiber links per TIA/EIA standards
Wave ID – automatic wavelength identification and switching
Dual Wave ID, single Wave ID, and CW
Large LCD with Backlight
Power measurements in dBm or µW; insertion loss in dB
Reference power level storage
Up to 500 test records storage per wavelength
USB port for download of stored records
AA alkaline, optional rechargeable NiMH battery pack or AC adapter
Low battery indicator
Free 50 µm and 62.5 µm mandrels
Cost-effective, easy to use
N.I.S.T. traceable
OPM 5-2C
The OPM 5 is used to perform diagnostic and evaluation measurements associated with fiber optic transmission systems and cable plant. Applications for the OPM 5 will be found within the telecommunication, cable television, data network, and industrial control industries.
The OPM 5 measures absolute power (in dBm or µW ) and loss (dB). Absolute power expressed in dBm is the amount of optical power received by the detector as compared to 1mW (0dBm=1mW). Measuring dBm is useful for verifying the output power of a transmitter and determining system losses.
Loss is the difference in optical power from a known input (the reference level) and the output power at the opposite end of the fiber under test. The OPM 5 can display dB loss directly after a reference level has been set. Loss measurements are used to qualify cable plant links and fiber optic jumpers.
Microwatts is also a way to measure absolute power. Some manufacturers specify their transmission equipment in watts instead of dBm. The OPM 5 offers the ability to measure watts for convenience when verifying output power of transmitters. For accurate results, always be sure to set the OPM 5 to measure the same wavelength as the output of the optical light source.
Specifications:
Calibration Wavelength (nm)
850, 1300, 1310,
1550nm
Tone Detection Range (dBm)
+6 to – 35
Tone Detection Frequency (Hz)
270 ± 13.5
1000 ± 50
2000 ± 300
Detector Type
Germanium (Ge)
Display Range (dBm)
+6 to -60 dBm
Accuracy (@ 25°C & -10.0dBm)
±0.25 dB
Resolution
0.01 dB (.1 dB selectable)
Battery Life
>30 hrs. typical operation with 9V Alkaline
Adapter Caps
Order Separately (ST, SC, FC and others available)
Size (H x W x H)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.56 lb (0.26 kg)
Operating Temp
0° to 50° C
Storage Temp
30° to 60° C
Relative Humidity
0 to 95% (non-condensing)
Optical Light Source OLS 1-Dual
Emitter Type
LED
Emitter Classification
Class 1, IEC 825
Spectral Width
40, 100 nm
Wavelength
850, 1300 nm
Stability (@25° C & 5 min. warm-up)
±.1 dB/8 hrs.
Output Power
Multimode (62.5/125 ìm)
-20 dBm @ 850 nm, -20 dBm @ 1300 nm
Singlemode (9/125 ìm)
-40 dBm @ 1300 nm
Power
40 hrs. typical operation with 9V alkaline, AC adapter optional
Optical Adaptors
ST or SC
Size (H x W x D)
4.6 x 2.6 x 1.2 in (11.6 x 6.6 x 3.1 cm)
Condition: Refurbished / Calibrated
Warranty: 90 Day Exchange
AFL NOYES OPM4 Singlemode 1310nm/1625nm & Multimode 850nm/980nm Loss Test Set
NOYES OPM 4-4C Optical Power Meter
850nm
980nm
1310nm
1480nm
1550nm
1625nm
NOYES OLS2 Dual Laser Source
1310nm
1550nm
Noyes OLS1 Dual Optical Light Source
850nm
1300nm
Includes Carrying Case & Accessories As Listed
OPM4-4 C OLS2-D OLS 1-D 1
Noyes OPM4 OLS2D OLS1D OPM-4 OLS-2D OLS-1D SM MM Fiber Loss Test Set Models On Sale Warranty Calibration Backed by The Best Service and Lowest Prices in the Industry.
OLS1 Dual Light Source
OPTICAL
OLS1-DUAL (SINGLE PORT)
Wavelength
850 ±30 nm
1300 +50/-10 nm
Emitter Type
LED,Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral Width
40 nm (typ)
120 nm (typ)
Output Power
>-20 dBm b
Output Stability
±0.1 dB over 8 hours (after 5-minute warm-up)
Fiber Size
62.5 µm c
GENERAL
Power
2 AA batteries, optional AC adapter
Battery Life
Typical 30 hours, minimum 20 hours
Available Adapters
SC, FC, ST
Operating Temperature
-10°C to 50°C, 90 % RH (non-condensing)
Storage Temperature
-30°C to 60°C, 90 % RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
OLS2 Dual Laser Source
The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port and offers several modes of operation. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.
Handheld, rugged, lightweight
Dual wavelengths from a single port
Dual or single Wave ID, CW, To
270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
Adjustable output
Low battery LED indicator
Long battery life with 2 x AA alkaline, optional AC adapter
Cost-effective, easy to use
N.I.S.T. Traceable
Applications:
Certify SM links per TIA/EIA standards
Fiber identification prior to splicing
Noyes OPM 4 – Adds Wave ID & Set Reference
The Noyes OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables.
The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.
The OPM 4-4C is calibrated at 850, 980, 1310, 1480, 1550, 1625 nm and designed for the higher power level requirements of long range, amplified optical spans used in CATV and DWDM networks.
Specifications:
Optical Specifications
OPM 4-4C
Calibrated Wavelengths (nm)
850, 980, 1310, 1480, 1550, 1625
Detector Type
Filtered InGaAs
Measurement Range (dBm)
+26 to -50
Accuracy (dB)
+-.25
Measurement Units
dB, dBm, uW
General Specifications
Power
typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Operating temperature
-10 to 50°C
Relative humidity
0 to 95% (non-condensing)
Storage temperature
-30 to 60°C
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
Condition: Refurbished
Warranty: 90 Day Exchange
Included
Noyes OPM 4-4C Optical Power Meter (BC# 13143)
-850nm
-980nm
-1310nm
-1480nm
-1550nm
-1625nm
-Interchangeable SC Connector
Noyes OLS1 Dual Light Source (BC# 13142)
-850nm
-1300nm
-Interchangeable SC Connector
Noyes OLS2 Dual Laser Source (BC# 13141)
-1310nm
-1550nm
-Interchangeable SC Connector
Noyes 5400-00-0201 Mandrell
Noyes 5400-00-0202 Mandrell
Fiber Cables:
-(2) SM SC-SC
-(2) MM SC-SC
User Manual On CD-ROM
Carrying Case (G)